Oxford Tig welder plus welding tips: A MIG welder uses a continually feeding spool of thin filler wire as an electrode fed by a wire feed gun to form an electric arc between a wire and the work-piece metal. This heats the work-piece metal and the electrode, causing them to melt and join together to create the weld. Mig welding can be either Gas or Gasless and each have benefits. Gasless welding is far more portable as there’s no gas bottle to carry around, saves cost on having to buy gas bottles and regulators, is easier on positional welds and can penetrate deeper than Gas MIG although the welding wire for a gasless MIG is more expensive than a gasless MIG. Gas MIG welding produces much cleaner welds with no slag or spatter, is slightly better on thinner metals and the welding wire is cheaper than gasless MIG wire.
OXFORD HYBRID chopper machines such as the MULTI-ARC models, CUTMAKER PLASMA, TIGMAKER & PULSE MIG models (I-MIG DP & S-MIG DP) offer a really sensible alternative to the inverter. They are still built around a rugged copper wound transformer but the hybrid chopper technology used in these works to give you superior welding performance, the lowest power consumption & the very high efficiency means the transformer is around half the size & weight of an older type machine. The electronics are simple & operate at the welding voltage level i.e. under 80V, there is only one PCB fitted & no microprocessor to cause software faults. So to sum up you get all the performance benefits of a good inverter but reliability is superb & you can expect a really long life span, equivalent to old type transformer machines, many times that of any inverter! Discover more info on Oxford Plasma Cutters.
Look for ways to support your hands. Having good support for your hands or arms is crucial for moving the torch with precise control. I do my best welding when the base of my hands or my wrists is supported in some way. Often you can rest your wrists on the part being welded. I keep an assortment of wood and metal blocks near my welding bench, and I often can get better support by positioning a block to rest my torch hand on. There are occasions where I rest my forearms, or even my elbows, on something for support. Many welders set up special support bars, positioned parallel to the joint being welded, and they slide their torch hand along the bar to help follow the joint with fine control. For some out-of-position work, I’ve had to rely on resting only my shoulder on something, and while not ideal, it’s better than having no support at all. Even placing my hip against something stationary can offer a bit of support, but I can’t weld very well when standing ‘free,’ with no support at all.
In many shops, the operator has to go to a tool room or supply area for a new contact tip, coil of wire or other welding accessory. This takes valuable time away from the welding cell and slows down overall productivity. To improve the operating efficiency and minimize wasted time, companies should stock at least a limited supply of all necessary items near the welding station – this includes shielding gas, flux and wire. Another helpful productivity enhancing tip is to switch to larger spools of wire such as from 25 lb. spools to 44 or 60 lb. spools to even larger packages of 1,000 lb. reels or 1,000 lb. drums. A simple switch like this means less changeover time, which adds up over the weeks, months and years. Shops should also be on the lookout for shielding gas waste. A simple device called a surge turbine can be placed at the end of the gun to provide a digital readout of the gas surge and flow rate. If the surge rate is high, investing in a surge guard can reduce the pressure, eliminating gas surges and waste. Leaks in the gas delivery system can also create a potential loss of money. By looking at the amount of consumables purchased each year and then examining the total gas purchased, a company can determine if there is a significant loss. Welding manufacturers and distributors should be able to provide average utilization figures so that loss can be detected. If there is a loss suspected, one of the easiest ways to check for leaks is to shut off the gas delivery system over the weekend. Check the level on Friday evening and then again on Monday morning to determine if gas was used while the system was in shut down mode. Explore more details at www.weldingsuppliesdirect.co.uk.