Altitude valve factory today: Different Types of Altitude Valves – Altitude valves come in various types, each designed to suit different applications and water systems. Let’s explore some of the different types of altitude valves available: Float-Controlled Altitude Valve: This type of valve uses a float mechanism to regulate the flow of water based on changes in water levels. It is commonly used in elevated tanks or reservoirs. Pilot-Operated Altitude Valve: These valves use a pilot system that controls the opening and closing of the main valve, allowing precise control over water levels. They are frequently used in high-rise buildings or industrial facilities. Pressure-Sustaining Altitude Valve: This type maintains constant pressure within a system by modulating the flow rate as needed, ensuring reliable performance even during peak demand periods. Discover even more details at altitude valve water tank.
Float control valve is a modulating valve that accurately controls the liquid level in tanks. This valve is designed to open fully when the liquid level reaches a preset low point, and close drip-tight when the level reaches a preset high point. The float pilot is remotely installed Inside of reservoir, or Integrally installed with main valve for size less than 4 Inch. Our hydraulic float valve can stop overflow or overfilling while the valve connector connects the valve to the incoming liquid. When the float rises to a selected level, the float level control valve is then opened or closed by the lever attached to the float.
FBGD is a double eccentric flange butterfly valve, with soft seal on the body, it has the lowest operational torque, much less wearing, the dovetail seal design has been proven over half century service with reliability. Features: The butterfly valve is made of DI body and DI disc; Advanced newly design with dovetail seal design and captured by epoxy on the back, with multiple raised ring to have more contact with disc but less friction during closure; The double eccentric design provides less contact area of seal with disc, and less stress at the open position of the disc; The disc design with arch shape and thru disc can provide better flow capacity, stronger and less weight . The shaft and disc connection with tangential pin which can be exchangeable and provide rigid connection. The DN 100-500MM use flat disc, and DN 600-1200MM use arch shape disc; Epoxy coated interior and exterior. Valve design meets or exceeds EN 593; Top flange connection meets ISO 5211-1982, and F/F meets EN 558-1 series 13 & 14.
NSCV- Non Slam Check Valve is used as protection against reverse flow when power failure in areas where noise pollution or water hammering is a critical issue. It can provide not only quiet performance but also low head loss. Features: High strength ductile iron body used for durability and less weight; Advanced dynamic design of single body with diffuser provides streamline flow and assures lower head loss; One of the lowest head loss check valve, big save in pumping power cost, valve disc with shorter stroker and spring reverse faster than most of check valve; Coated with powder epoxy both inside & outside for corrosion resistance; Bronze bushing reduce wearing problem during operation; Hydrodynamic design with spring ensures non slamming and water hammerless; Stainless steel spring hidden in the diffuser under protection while valve in operation; Disc will positively close before reverse flow, and maximize the closing speed up to 0.2 Sec; Installation can be vertical/horizontal/ inclined. For size DN800 and up preferred vertical installation. ·Comply with EN 558-1, ISO 5752 and EN 1092-2, ISO 7005-2 flange dimension. Find even more info at shsuotevalve.com.
What is an Altitude Valve? An altitude valve, also known as an altitude control valve or altitude regulator, is a type of valve used in water distribution systems. It is designed to maintain a specific water level or pressure within a storage tank or elevated structure. The purpose of an altitude valve is to control the flow of water into or out of a storage tank to maintain a predetermined level or pressure. It functions by automatically opening and closing based on changes in water level or pressure. When the water level or pressure drops below the desired set point, the altitude valve opens to allow water to flow into the tank, replenishing the supply. Conversely, when the water level or pressure rises above the set point, the valve closes to prevent overfilling or excessive pressure.
We are committed to producing the best quality products at the most competitive prices. Therefore, we sincerely invite all interested companies to contact us for more information. Our objective is “good quality for survival, good faith for development, using new technology to improve product quality”. Our valves are produced to the highest quality standards with modern manufacturing technology and astute materials sourcing. Most of our certificated products sell to over 36 cities in Europe, North America, South America, Africa, etc. As a full-service valve supplier, we have 18 years manufacturing experience in producing various industrial valves. Our production workshop based in China is equipped to provide a professional custom valve service.